Alian Electronics
  • Home
    • Warranty info
    • Freight Information
    • Creating a New Product >
      • The Discovery Process
      • Intellectual Property
      • The Quotation
      • Designing the Control Circuit
      • Designing the Circuit board
      • Building the Prototype
      • Writing the Software
      • Field Trials
      • Product Compliance issues
      • Production
      • Manuals & Documentation
  • Pump Control Products
    • SM256 Dual Pump Controller
    • SM268 Dual Pump Controller
    • SL96 Level Sensor
  • ANDON
  • DC Motor Controls
    • SM263 Motor Controller
    • SM267 Display for the SM263
    • SM275 Test Console
  • Electronic Kits
    • SM361 Rig Switch kit
    • SM204/SM205 DF Hunt Kits
  • Other Products
    • SM285 Wiper Delay Unit
    • SM108B Door Interlock System
    • SM106 DC Converter
    • SM171 12 Input, 12 Relay controller
    • SM195 Roller Shutter Controller
    • SM231 An RS232 to RS422/RS485 Adapter
    • SM271 Power Quality Analyser
  • Contact
    • Email
    • Location map
  • About Alian
    • Achievements
Picture

SM263  MOTOR CONTROLLER

Introduction

The SM263 is a compact, general purpose DC motor controller. It is available in  12V and 24V versions, with a steady output of up to 80 Amps.  It has a range of features to suit different situations that may be selected by the installer.

Standard features include:

  •           LOW BATTERY WARNING
  •           DAMPENED ACCELERATION
  •           ON-BOARD FORWARD / REVERSE / BRAKE   CONTROL
  •           STALL & OVER CURRENT PROTECTION
  •           SIMPLE 2-WIRE CIRCUIT MANAGES POWER ON/OFF, SPEED & DIRECTION
  •           SUPPORTS REDUCED SPEED IN REVERSE
  •           SUPPORTS SELF-TEST & SAFETY CHECKS UPON POWER UP
  •           SUPPORTS DYNAMIC (RESISTIVE LOAD) BRAKING

Picture


An optional backlit Liquid Crystal Display (SM267) can be fitted to give the operator information on battery condition, drive status and system integrity


Protection Features
Four levels of protection from stalled motor events. Should a full locked-rotor stall occur, a rapid beep will warn the operator that a brief power reduction down to 30% drive will occur if they persist.  Additional safety software monitors the integrity of the power semiconductors when the throttle is at rest. The software which will automatically isolate the motors should any drive fault conditions be detected, making it a very safe controller to use. 

When first activated, the throttle must be at-rest in the Forward direction, or warning beeps will sound and the controller is disabled until this is done. This safety feature guards against the possibility of a runaway vehicle if the throttle was rotated before battery power was first applied.

Direction Control Motor rotation activity is monitored by the microprocessor to prevent the user going into hard reverse while still moving or rolling forwards.  This protects both the user from experiencing sudden changes in acceleration and protects a gearbox and drive components from mechanical stress damage. 

Simple Connections
The controller supports one or two 12V motors, or one 24V motor.  Throttle Potentiometer, Key switch, Forward/Reverse switch all connect via a single wire loop circuit.  The display connects via a common RJ12 (telephone style) patch cable.


Picture
SPECIFICATIONS:
           
                        Motor Type supported:                D.C. Permanent Magnet
                        Supply Voltage:                               12 or 24VDC
                        Output current:                              80 Amps (nominal)
                        Dimensions:                                     288 x 70 x 34mm
                        Weight (controller)                        124g
                        Power connections:                       6.3mm vertical tab
                        Direction Control                            Relay switched ‘H’ bridge
                        Speed Control:                                 0-100% PWM via 5 MOSFETS
                        Current Sensing:                              Hall Effect
                        Throttle Control                              0 - 2,500 Ohms spread required

Click on the link below to download this information sheet and the full support manual.

sm263_flyer.pdf
File Size: 93 kb
File Type: pdf
Download File

sm263_manual.pdf
File Size: 471 kb
File Type: pdf
Download File

_________________________________________________________________________________________________________________

PRICING INFORMATION   
  • Payment can be made to Alian Electronics via EFT or Pay Pal
  • All prices in $AUD and do not include the cost of freight.   (Click HERE to view the Freight Information page)
  • When buying from within Australia add 10% GST
  • (Overseas sales are GST Free, but depending upon local policy, you may need to pay tax/duty for goods to be released by your Customs)
  • When buying from within Australia by Pay Pal, add 2.4% for Pay Pal transaction fee.
  • When buying from Outside Australia by Pay Pal add 3.6% for Pay Pal transaction and currency conversion fee.
  • (When buying from Outside Australia using Telegraphic Transfer ( TT ) the buyer will pay transaction fees with their bank.)
  • Transaction details, Freight & other charges will be shown on a Proforma Invoice supplied to you before you pay.

        SM263  Motor Controller
                        Qty 1-9        $293.00
                        Qty 10+       $237.00

        SM267  LCD Display Module
                        Qty 1+         $49.50
                        Qty 10+       $45.50

        SM275  Test Console
                        Qty 1+           $36.00



         (last updated August 2019) 

_________________________________________________________________________________________________________________

Powered by Create your own unique website with customizable templates.