Other Products

SM118 Flashing Forklift Safety Sign

This Forklift Safety Sign will flash each second to remind pedestrians that a forklift is operating in the area. It is 304 x 216mm (approximately A4 size) and can operate from 12V or 24V.

Useful for areas where pedestrians and forklift traffic must mix. It may be fitted with a Passive Infrared (PIR) sensor to trigger the sign flash with movement in key vehicle areas.

Click for more information

SM107 Forklift Driver Seatbelt Interlock System

The SM107 Forklift operator safety interlock ensures that when the Handbrake is ON and the Seat Switch and Seatbelt Buckle have been operated in the correct sequence will the vehicle ignition be armed.
This unit ensures that Forklifts can be compliant with Australian Standards ISO 3691.8 on driver restraint, which has been mandatory since September 2013.

Click for more information...

SM285 Windscreen Wiper Delay module

This unit provides the necessary time delay for windscreen wipers as used in many brands of cars and trucks dating back to the Ford Cortina in the 1970's. They are also used in many other Fords such as the F150 and F250. It is a direct plug-in replacement for the Bosch unit 9330065009, which is no longer manufactured.

When in use, it provides a fixed time delay of four seconds between windscreen wipes.

Click for more information...

SM93 Battery Monitor & low voltage cutout

The SM93 Battery Monitor is intended for use with electric forklifts and vehicles operation from a 12V, 24V, 36V, 48V supply. It displays a slowly changing value 0-9 which represents battery state-of-charge. It also contains a small control relay that can be used to 'lock out' hydraulic lift control (or similar accessory) where the vehicle has been used too long with a flat battery and the battery bank integrity is at risk.

Click here for more information...

SM106 DC to DC converter, 12V 3Amp output

More than just a simple converter, this unit will change a supply voltage from 20 to 55Volts down to 12V. Heavy filtering makes it survive in harsh electric forklift environments that would destroy conventional converters. Output is clean and suitable for reversing cameras, LED lighting etc. Additional internal reinforcement assists in high-vibration environments.
The SM106 is now used widely in both Australia and New Zealand for forklift and fleet vehicles.

Click for more information...

SM108 Direction Analyser for infrared sensors

Where an infrared beam must be placed across a driveway, doorway or factory entrance, false alarms by bugs, birds etc are a problem. This unit supports two infrared beams so that both beams must break to trip a door chime or alarm. Direction of travel is also detected, so that a different chime may be used when people enter or leave. (Your staff only need to react when people enter the building) A third output reacts if a vehicle blocks both beams. Also works with driveway hoses and mat sensors.
(sensors not included)

Click for more information...

SM108B Versatile Door interlock for Bathroom/Utility rooms with 2 doors

This is a flexible door control system with FOUR different plans of operation to suit a range of situations. Where a bathroom/Utility room is being shared between two other rooms, this system will automatically or manually lock one or both doors via electric latches. Privacy plans can ensure that occupants of one room cannot gain access to the second room via a shared room in the middle. Electric locks default to 'unlocked' state during emergencies and power outages. Choose a plan that suits your circumstances. Great for Hotels, nursing homes, hospitals or even private homes where two kids must share a common bathroom.

Click for more information...

SM136 Universal 3-Channel timer module

The SM136 is a Three Channel Timer module with three independently working timer circuits. Each timer circuit has an optically isolated Input Trigger, a Timer Adjustment control knob, a Timer Scale option link and a 30 Amp output relay. Each control knob may adjust the delay between 0 and 25 seconds or 0 and 4.2 minutes (link selectable).

Click for more information..

SM155 Vehicle Battery Linker

The SM155 supports a second battery in motor vehicles. When the engine is running, this unit detects the voltage rise and links the batteries, so that they both charge. They auto-isolate when the engine stops, so you can flatten your second battery and still drive away. Also features pushbutton jump-start from the 2nd batt and a 90 minute timer to deactivate CB radio's etc. if the vehicle is unattended.

Click for more information...

SM171 12 input, 12 Relay Control Module

This is a generic control platform where Alian Elect can apply programming of your choice, or if you are familiar with Atmel microprocessors, experiment with your own software. Comes with a test program where 12 inputs activate 12 outputs & echo the result to the serial port.

Click for more information...

SM195 Roller Door/Roller Shutter controller

The SM195 module is used in conjunction with roller doors and roller shutters. On some installations there is a centre-off key switch where the operator can send a shutter Up or Down, however if they go direct from Up to Down, they can stall or short out the door motor. With the SM195 in-line with the key switch, it will make sure that the shutter has stopped moving completely before the motor direction may be changed.

Click for more information...

SM218 Pillar Cabinet Clip (for field technicians)

This is a useful item for Telephone Company staff that must make frequent connections to pillars and cabinets in the field. The two clips are spaced for standard pillar terminals and have an independent action. Cables that connect to test phones and equipment are via easily replaceable RCA patch leads. A good time saver for repetitive work.

Click for more information...

SM231 RS232 to RS422/RS485 Adapter

A compact interface between RS232 and RS422/RS485 signals. Bi-directional and usually encapsulated in a tough heatshrink sleeve. RS232 side is via a DB9 connector RS422 side is via RJ45 connector. May be externally powered via 12 volt plug pack (not included).

Click for more information...

SM254 Serial/Wireless 1 x 16 character Large-Text LCD Display Module

This display has 16 very large character positions where the display needs to be easy to read. It is controlled serial data and is available both as a hard-wired version or as wireless remote version.

Click for more information...

SM264 Serial 2 x 16 character LCD display module (with 5-button keypad)

This is a generic 2 line, 16 character, backlit LCD module adapted for serial control over a single cable for a number of Alian products. It has embedded 3mm mounting threads and a cluster of push-buttons, usually configured as 'Up/Down, Left/Right, Ok.' Screen is serially refreshed 10 times per second.

Click for more information...

SM265 Serial 2 x 16 character LCD display module (no keypad)

This generic 2 line, 16 character, backlit LCD module is similar to the SM264 display module, but without the 5-button keypad

Click for more information...

SM267 Serial 2 x 16 character LCD display (no keypad, no mounting studs)

This is a generic 2 line 16 character, backlit LCD module. It is functionally similar to the SM264, SM265 except that it has no keypad and no 3mm mounting threads embedded within the corners of the module. This makes it more compact than the other module types, making it ideal for tight situations. It also uses a smaller microprocessor which helps to keep unit costs low.

Click for more information...

SM269 4-Pole 30A contactor with 12V drive

4-pole contactors that work from 12V are difficult and expensive to obtain. This module supports 3 x 30 Amp relays and 1 x 10A relay. The relays may be driven directly via a 12V source or via an on-board MOSFET driver, making it ready to operate directly from a microprocessor port without additional hardware.

Click for more information...

SM271 Power Quality Analyser

The SM271 is used to check the integrity of 240VAC power capability at any given location. It measures the supply, then applies a 3.8kW load for 1 second and measures again. The voltage drop is displayed and gives the operator an indication of the quality of the power cabling and how many kw may be supported at that site. Great when dealing with motor loads operating in fringe areas, where the customer needs to be convinced that their cabling needs to be upgraded.

Click for more information...

LED Lighting Information

LED Lighting information
Some information about Alian Electronics LED lighting can be viewed here

Click for more information...