Alian Electronics
  • Home
    • Warranty info
    • Freight Information
    • Documents
  • Pump Control Products
    • SM256 Dual Pump Controller
    • SM268 Dual Pump Controller
    • SL96 Level Sensor
  • ANDON
    • ANDON
    • CLOCK VIEW
  • DC Motor Controls
    • SM263 Motor Controller
    • SM267 Display for the SM263
    • SM275 Test Console
  • Electronic Kits
    • SM456 Morse Code Clock Kit
    • SM361 Rig Switch kit
    • SM204/SM205 DF Hunt Kits
  • Other Products
    • SM285 Wiper Delay Unit
    • SM108B Door Interlock System
    • SM106 DC Converter
    • SM171 12 Input, 12 Relay controller
    • SM195 Roller Shutter Controller
    • SM231 An RS232 to RS422/RS485 Adapter
    • SM271 Power Quality Analyser
  • About Alian
    • Achievements
    • Contact >
      • Email
      • Location map
Picture

SM302  DUAL  SPRAY  VALVE / SPRAY PUMP CONTROLLER


GENERAL DESCRIPTION

In situations where one or two spray valves or pumps, deliver water to a tank that can only discharge at a slow rate, there is a risk of overflow.    The SM302 is designed to treat this problem

By passing the spray valve or pump control through the SM302, a High Level Alarm sensor can report faults by relay contact , audible alarm, and flashing LED lamp.  In the event of a High Level Alarm it will isolate the spray valves until levels have fallen.


An adjustable timer (settable between zero and 200 seconds) will provide a 'wait' time after a High Level Alarm.  It will inhibit the two output relays until there has been sufficient drain time in the sump tank.  This prevents excessive cycling of output sprays. 

Unit will switch 24V or 240V AC loads.  Built in hour meter also tracks hours of flow operation.

The control unit has several presettable options that may be engaged by the installer to suit a range of field installations.  A Liquid Crystal Display (LCD) provides additional information about the status and operation of the unit.  An internal Hour Meter may be viewed which tracks the number of hours and minutes that each output has operated since the system was first installed.


Picture

  • The module is 155 x 115mm.  It is housed in an IP66 enclosure, 125 x 165 x 75mm, to keep it free of dust, moisture and to limit access by non-technical staff. 
  • Each 240VAC output terminal block can support a load to1500 watts, 7.5A.  All electrical connections (except for the display socket) are via green unplugable screw terminal blocks.  
  • A large LED and Piezo beeper are present on the board to signal overflow alarm conditions.
  • A relay controlled 24V, 200ma AC outlet is provided via a 2-way terminal block, to drive an external spray solenoid.  This is protected by a 1.5A, M205 style fuse.
  • Each of the three power relays have an associated red ‘status’ led to indicate relay activity.  A single red LED labeled ‘Power’ indicates that mains is connected to the unit.
  • A four-way terminal block provides the termination point for up to three moisture conductivity or level probes relative to a common conductor.   Probes may be simple conductive metal pins placed within the tank enclosure, or commercial (normally open) float-type level switches. (probe signals are intrinsically safe with less than 5V at less than 1ma of current)
  • A 3-way terminal block provides the termination point for two momentary-action push button switches. The JOG switch will force a 20 second operate cycle for both switched outputs.  The Alarm Mute switch trips a 6-hour Alarm Mute timer which will block the sound of the audible alarm beeper for 6 hours during high-level alarm.
  • Two option links labeled LK1 and LK2 may be placed into either an A or B position to select installation options.   LK1 may be used to ‘Fast Forward’ several of the internal time delays to allow installers to test a system without having to wait for long time periods.  ( LK2 is not in use with this model controller)
  • A small, blue 10-position rotary selector switch is present to select one of several views on the display for the operator to monitor the system status and to adjust wash down spray delay times from 1 to 6 hours.
        
Click on the link below to download this Product Information or the Operator Manual.
sm302_flyer.pdf
File Size: 555 kb
File Type: pdf
Download File

sm302_manual_v1.pdf
File Size: 1271 kb
File Type: pdf
Download File

_________________________________________________________________________________________________________________

PRICING INFORMATION   
  • Payment can be made to Alian Electronics via EFT or Pay Pal
  • All prices in $AUD and do not include the cost of freight.   (Click HERE to view the Freight Information page)
  • When buying from within Australia add 10% GST
  • (Overseas sales are GST Free, but depending upon local policy, you may need to pay tax/duty for goods to be released by your Customs)
  • When buying from within Australia by Pay Pal, add 2.4% for Pay Pal transaction fee.
  • When buying from Outside Australia by Pay Pal add 3.6% for Pay Pal transaction and currency conversion fee.
  • (When buying from Outside Australia using Telegraphic Transfer ( TT ) the buyer will pay transaction fees with their bank.)
  • Transaction details, Freight & other charges will be shown on a Proforma Invoice supplied to you before you pay.

        SM302  Dual Spray Valve Controller
                        Qty 1-9        $357.00
                        Qty 10+       $330.00


          (last updated April 2023) 
_________________________________________________________________________________________________________________